Installation guide
From Psychosynth
(→Dependencies) |
|||
| Line 20: | Line 20: | ||
* libvorbis (needed for OGG vorbis file support) | * libvorbis (needed for OGG vorbis file support) | ||
* SoundTouch (needed for sample stretching) | * SoundTouch (needed for sample stretching) | ||
| + | * Sigc++ 2.0 | ||
| + | * Boost Threads and Filesystem | ||
|} | |} | ||
| Line 25: | Line 27: | ||
<pre> | <pre> | ||
| − | apt-get install automake libtool libogre-dev libois-dev libcegui-mk2-dev libasound2-dev libjack-dev liblo0-dev libsndfile-dev libxml2-dev libsoundtouch1-dev libvorbis-dev | + | apt-get install automake libtool libogre-dev libceguiogre-dev libois-dev libcegui-mk2-dev libasound2-dev libjack-dev liblo0-dev libsndfile-dev libxml2-dev libsoundtouch1-dev libvorbis-dev libboost-serialization1.35-dev libboost1.35-dev libsigc++-2.0-dev |
</pre> | </pre> | ||
| − | + | If you are compilling the *bzr* version you have to enter this command: | |
| − | + | ||
<pre> | <pre> | ||
| − | + | autoreconf | |
</pre> | </pre> | ||
| − | + | <pre> | |
| + | ./configure | ||
| + | make | ||
| + | sudo make install</pre> | ||
| − | + | And then run the program simply typing: | |
| − | + | <pre>psynth3d</pre>. | |
| − | <pre> | + | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
== Installing == | == Installing == | ||
| Line 71: | Line 70: | ||
psynth3d | psynth3d | ||
</pre> | </pre> | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Revision as of 19:58, 8 February 2009
First of all you must get a copy of the sources of this program. Go to the download section if you do not have them yet. Note that this document is only to install from the sources -if there is a binary package for your distribution, use that instead.
Dependencies
Then, to try the software you will need these third party libraries and programs:
|
|
In Debian and Ubuntu you can install all those dependencies with the following command. Anyways, I suggest installing liblo from the original sources because the version in the repositories is outdated and contains a bug:
apt-get install automake libtool libogre-dev libceguiogre-dev libois-dev libcegui-mk2-dev libasound2-dev libjack-dev liblo0-dev libsndfile-dev libxml2-dev libsoundtouch1-dev libvorbis-dev libboost-serialization1.35-dev libboost1.35-dev libsigc++-2.0-dev
If you are compilling the *bzr* version you have to enter this command:
autoreconf
./configure make sudo make install
And then run the program simply typing:
psynth3d.
Installing
If you downloaded the program from Bazaar you will first need to generate the compilation scripts:
autoreconf
Now you will need to run the configuration script to detect the the libraries and set up the compilation settings.
./configure
Check that everything has been detected correctly and then compile the program:
make
At last we must run these commands with superuser privileges to install:
make install ldconfig
We can now run the 3D simulator:
psynth3d
