Installation guide

2008-10-27T23:35:29Z

Blackhold: /* Dependencies */

{{Languages}}

First of all you must get a copy of the sources of this program. Go to the [[download]] section if you do not have them yet. Note that this document is only to install from the sources -if there is a binary package for your distribution, use that instead.

== Dependencies ==

Then, to try the software you will need these third party libraries and programs:
{|cellspacing="20px"|
|
* GNU Autotools (only for the SVN version)
* Ogre (needed by the 3D interface)
* CEGUI (needed by the 3D interface)
* OIS (needed by the 3D interface)
* liblo (needed for the network support)
* libxml2 (needed for XML config support)
|
* Alsa (needed for ALSA sound output)
* Jack (needed for Jack sound ouput)
* libsndfile (needed for pcm file support)
* libvorbis (needed for OGG vorbis file support)
* SoundTouch (needed for sample stretching)
|}

In Debian and Ubuntu you can install all those dependencies with the following command. Anyways, I suggest installing ''liblo'' from the original sources because the version in the repositories is outdated and contains a bug:

<pre>
apt-get install automake libtool libogre-dev libois-dev libcegui-mk2-dev libasound2-dev libjack-dev liblo0-dev libsndfile-dev libxml2-dev libsoundtouch1-dev libvorbis-dev
</pre>

When installing using bzr files previous you have to install some dependencies before (tested on lenny), use dpkg -l |grep libboost to check that previous version is not installed, if is installed remove all packets that shows the output of dpkg -l |grep liboost

<pre>
# apt-get install libboost-serialization1.35-dev libboost1.35-dev libsigc++-2.0-dev
</pre>

then continue with the following installation (first check that file configure.ac has commented this line: PACKAGE_DATA_DIR="./data")

<pre># autoreconf</pre>

<pre># ./configure</pre>

<pre># make</pre>

and then run the program simply typing psynth3d, if the program gives you the output: ''[/alsa] WARNING: Could not write to device. (Broken pipe)'' change the audio to oss in config menu.

== Installing ==

If you downloaded the program from Bazaar you will first need to generate the compilation scripts:
<pre>
autoreconf
</pre>

Now you will need to run the configuration script to detect the the libraries and set up the compilation settings.
<pre>
./configure
</pre>

Check that everything has been detected correctly and then compile the program:
<pre>
make
</pre>

At last we must run these commands with superuser privileges to install:
<pre>
make install
ldconfig
</pre>

We can now run the 3D simulator:
<pre>
psynth3d
</pre>

Installation guide

2008-10-25T13:10:41Z

Blackhold: /* Dependencies */

{{Languages}}

First of all you must get a copy of the sources of this program. Go to the [[download]] section if you do not have them yet. Note that this document is only to install from the sources -if there is a binary package for your distribution, use that instead.

== Dependencies ==

Then, to try the software you will need these third party libraries and programs:
{|cellspacing="20px"|
|
* GNU Autotools (only for the SVN version)
* Ogre (needed by the 3D interface)
* CEGUI (needed by the 3D interface)
* OIS (needed by the 3D interface)
* liblo (needed for the network support)
* libxml2 (needed for XML config support)
|
* Alsa (needed for ALSA sound output)
* Jack (needed for Jack sound ouput)
* libsndfile (needed for pcm file support)
* libvorbis (needed for OGG vorbis file support)
* SoundTouch (needed for sample stretching)
|}

In Debian and Ubuntu you can install all those dependencies with the following command. Anyways, I suggest installing ''liblo'' from the original sources because the version in the repositories is outdated and contains a bug:

<pre>
apt-get install automake libtool libogre-dev libois-dev libcegui-mk2-dev libasound2-dev libjack-dev liblo0-dev libsndfile-dev libxml2-dev libsoundtouch1-dev libvorbis-dev
</pre>

When installing using bzr files previous you have to install some dependencies before (tested on lenny), use dpkg -l |grep libboost to check that previous version is not installed, if is installed remove all packets that shows the output of dpkg -l |grep liboost

<pre>
# apt-get install libboost-serialization1.35-dev libboost1.35-dev libsigc++-2.0-dev
</pre>

then continue with the following installation

<pre># autoreconf</pre>

<pre># ./configure</pre>

<pre># make</pre>

and then run the program located on src/psynth3d

---
''when you run psynth3d it works but asks for selecting renderer, but when you push de button the program closes and gives that output: ''
<pre># ./psynth3d
[/xmlconf] ERROR: Could not open config file for reading: /root/.psychosynth/psychosynth.xml
[/gui] INFO: Loading settings.
[/xmlconf] ERROR: Could not open config file for reading: /root/.psychosynth/psynth3d.xml
[/gui] INFO: Initializing Ogre.
Warning: Tried to connect to session manager, Authentication Rejected, reason : None of the authentication protocols specified are supported and host-based authentication failed
Error: Shell widget menu has zero width and/or height</pre>
--[[User:Blackhold|Blackhold]] 15:10, 25 October 2008 (CEST)

== Installing ==

If you downloaded the program from Bazaar you will first need to generate the compilation scripts:
<pre>
autoreconf
</pre>

Now you will need to run the configuration script to detect the the libraries and set up the compilation settings.
<pre>
./configure
</pre>

Check that everything has been detected correctly and then compile the program:
<pre>
make
</pre>

At last we must run these commands with superuser privileges to install:
<pre>
make install
ldconfig
</pre>

We can now run the 3D simulator:
<pre>
psynth3d
</pre>

Psychosynth - User contributions [en]

Installation guide

Installation guide